Display:

Backlit dimmable LCD display
Upper line: 6-digit, three-color (red, green, orange) with 18 mm digits
Lower line: 9-digit, green with 8.9 mm digits

Physical unit:

A physical 3-digit (red, green or orange) unit can be easily programmed from a list.

Indicators:

Four red backlit indicators for switching outputs.

Keyboard:

4 buttons, whereby 2 buttons are freely programmable function buttons
are freely programmable function keys.

Counter displays:

6-digit (top line) or 9-digit (bottom line)
Top line: -199,999 to 999,999
Bottom line: -199,999,999 to 999,999,999

Speedometer displays:

6-digit (upper or lower line)
Tachometer A or tachometer B:
0 to 999,999
Speedometer C or maximum values:
-199,999 to 999,999
Maximum input frequency: 50 kHz
Minimum input frequency: 0.001 Hz
Display update time: 0.1 to 999.9 seconds
Accuracy: +/-0.01%

Input A and B:

NPN, PNP sensors, CMOS, TTL, potential-free contacts, permanent magnet sensors are accepted. Setting via DIP switch.
Damping adjustable to 50 Hz.
Minimum input frequency for tachometer: 0.01 Hz
Maximum input voltage: 30 VDC
In dual counter mode with rotary encoder, user inputs 1 and/or 2 are also used as signal inputs. These user inputs are set to an NPN input without damping as standard. The damping against contact bounce of a mechanical input signal must be provided externally.

Sensor supply:

+ 18 VDC @ 60 mA DC max;
±5 %, short-circuit proof.

User input:

Three programmable user inputs
NPN or PNP switching (adjustable via jumper), response time: 12 msec. when activating or deactivating,
max. input signal: 30 VDC
NPN switching
(20 kOhm pull-up resistor to +3.3 V):
Active at_Vin <1.1 V;
Inactive at_Vin >2.2 V
PNP switching
(20 kOhm pull-down resistor):
Active at Vin >2.2 V;
Inactive at_Vin <1.1 V

Programming:

Programming is carried out either via the integrated USB interface and the free Crimson 2 programming software or via the four front buttons. The simple and logically structured menu navigation allows very fast commissioning. In addition, access rights can be assigned, e.g. quick access to the switching points can be enabled. The Crimson 2 software is available as a free download.

Power supply:

40 VAC to 250 VAC, 50/60 Hz, 20 VA or 21.6 VDC to 250 VDC, 8 W.
Isolation up to 2,300 _Vrms for 1 minute to all inputs and outputs.

Data backup:

Non-volatile data memory

Ambient temperature:

Operation: 0 °C to +60 °C.
Storage: -40 °C to +60 °C.

Relative humidity:

max. 85%. rH, non-condensing.

Protection class:

Jet-proof and dust-tight to IP65 from the front. Rear protection class IP20.

Housing:

Black, impact-resistant plastic housing made from a single cast. The electronic slot can be pulled out to the rear. The plug-in cards can be installed very easily.

Dimensions:

W 97 mm x H 50 mm x D 105 mm.

Panel cut-out:

according to DIN: 92 mm x 45 mm.

Fastening:

via mounting frame with clamping screws.

Connection:

Via screw terminals.

Weight:

approx. 227 g.

Scope of delivery:

Device, fixing material, seal, operating instructions.

Customs tariff number:

9030 33 70

Manufacturer:

Red Lion, USA

Output cards:

The device can be upgraded very quickly with various output cards. Each device can be equipped with a maximum of one interface card, one relay or transistor output card and one analog output card. The installation of the cards is simple and intuitive.

Pluggable interface card:

1. half-duplex RS232, programmable (terminal strip or plug).
2. multipoint RS485, programmable (terminal strip or plug).
3. DeviceNet, programmable.
4. PROFIBUS-DP, programmable

Pluggable relay output cards:

• 2 x relay changeover contact 5 A at 120/240 VAC or 28 VDC (ohmic load), at 120 VAC (80 VA inductive load). Service life of the relays is 100,000 cycles at max. load. The service life increases with lower loads.
• 4 x NO relay 3 A at 240 VAC or 30 VDC (resistive load), at 120 VAC (80 VA inductive load). Service life of the relays is 100,000 cycles at max. load.

Pluggable transistor output cards:

• 4 x NPN-OC transistors: max. 100 mA at _Vsat = 0.7 V, _Vmax 30 V, galvanic isolation of 500 V from the signal input.
• 4 x PNP-OC transistors: Internal supply: 24 VDC +/-10%, max. 30 mA all 4 transistors. External supply: max. 30 VDC, 100 mA for each individual transistor.

Pluggable analog output card:

Selectable output signal: 0/4 mA to 20 mA, 0 VDC to 10 VDC. Digitally scalable, offset. Accuracy: 0.17 % of range at 18 °C to 28 °C operating temperature, 0.4 % of range at 0 °C to 50 °C operating temperature. Resolution 1/3500. Voltage: 10 VDC (500 Ohm max. load). Current: 20 mA (500 Ohm load max.). Galvanically isolated from the signal input up to 500 V.