Display:

3-color backlit dimmable LCD display.
The display is divided into 7 programmable color zones (1st line, 2nd line, 4 universal physical units and indicators).
Line, 4 universal physical units and indicators).
Upper and lower line each with 4 digits, display range -1999 to
9999, programmable unit (3 digits) and 8-segment bargraph.

Universal indicators:

Up to four programmable indicators
with 2 digits each

Status indicators:

MAN: Controller is in manual mode.
REM: Controller is in remote mode.

Digit height:

Vertical installation: 1st row: 13 mm, 2nd row: 11.2 mm
Horizontal installation: 1st line: 15.7 mm, 2nd line: 12 mm

Keyboard:

4 buttons, whereby 2 buttons are freely programmable function buttons
are freely programmable function keys.

Resolution:

24 bits of the internal A/D converter.

Update rates:

A/D conversion rate: programmable from 5 to 40 measurements/sec,
depending on the type of sensor connected.
Display update: 1 to 20 updates/sec.
Switching output: delay time from 0 to 9,999 seconds
Analog output: update time from 0 to 10 seconds

Data backup:

FRAM

Error messages:

"OLOL" - input signal is greater than the + signal range
"ULUL" - input signal is smaller than the - signal range
"Short" - sensor short circuit is present (Pt100 only)
"OPEN" - sensor break is present
"...." -Display value exceeds upper display value
"-....." -Display value falls below lower display value

Entrance areas:

The accuracy in the range table (see drawings) is given as a percentage of the display value. The protection corresponds to the max. permissible input signal. Range adjustable via jumper.

Sensor supplies:

• Ext. sensor supply: +18 VDC @ 50 mA
• Reference voltage: +2 VDC, +/-2%
  Requirement: 1 k load min. (2m A max.)
  Temperature coefficient: 40 ppm/°C max.
• Reference current: 1.05 mA, +/-2%
  Requirement: 10 k load max.
  Temperature coefficient: 40 ppm/°C max.

User input:

Two programmable user inputs
NPN or PNP switching, max. input signal: 30 VDC
NPN switching (20 kOhm pull-up resistor to +3.3 V):
Active at_Vin <1.1 V; Inactive at_Vin >2.2 V
PNP switching (20 kOhm pull-down resistor):
Active at Vin >2.2 V; Inactive at_Vin <1.1 V

Ambient conditions:

Temperature: 0 °C to +50 °C. Storage: -40 °C to +60 °C.
Humidity: max. 85%rh, non-condensing.

Power supply:

40 VAC to 250 VAC, 50/60 Hz, 20 VA or 21.6 VDC to 250 VDC, 8 W

Protection class:

Jet-proof and dust-tight to IP65 from the front.
Rear protection class IP20.

Programming:

Programming is carried out either via the integrated USB interface and the free Crimson 2 programming software or via the four front buttons. The simple and logically structured menu navigation allows very fast commissioning. In addition, access rights can be assigned, e.g. quick access to the switching points can be enabled.

Housing:

Black, impact-resistant plastic housing made from a single cast. The electronic slot can be pulled out to the rear. The plug-in cards can be installed very easily.

Dimensions:

W 97 mm x H 50 mm x D 105 mm.

Panel cut-out:

according to DIN: 92 mm x 45 mm.

Fastening:

via mounting frame with clamping screws.

Connection:

Via screw terminals.

Weight:

approx. 227 g.

Scope of delivery:

Device, fixing material, seal, operating instructions.

Customs tariff number:

9032 89 00

Manufacturer:

Red Lion, USA.

Output cards:

The device can be upgraded very quickly with various output cards. Each device can be equipped with a maximum of one interface card, one relay or transistor output card and one analog output card. The installation of the cards is simple and intuitive.

Pluggable interface card:

1. half-duplex RS232, programmable (terminal strip or plug).
2. multipoint RS485, programmable (terminal strip or plug).
3. DeviceNet, programmable.
4. PROFIBUS-DP, programmable
5. Modbus RTU/ASCII

Pluggable relay output cards:

• 2 x relay changeover contact 5 A at 120/240 VAC or 28 VDC (ohmic load), at 120 VAC (80 VA inductive load). Service life of the relays is 100,000 cycles at max. load. The service life increases with lower loads.
• 4 x NO relay 3 A at 240 VAC or 30 VDC (resistive load), at 120 VAC (80 VA inductive load). Service life of the relays is 100,000 cycles at max. load.

Pluggable transistor output cards:

• 4 x NPN-OC transistors: max. 100 mA at _Vsat = 0.7 V, _Vmax 30 V, galvanic isolation of 500 V against the signal input.
• 4 x PNP-OC transistors: Internal supply: 24 VDC +/-10%, max. 30 mA all 4 transistors. External supply: max. 30 VDC, 100 mA for each individual transistor.

Pluggable analog output card:

Selectable output signal: 0/4 mA to 20 mA, 0 VDC to 10 VDC. Digitally scalable, offset. Accuracy: 0.17 % of range at 18 °C to 28 °C operating temperature, 0.4 % of range at 0 °C to 50 °C operating temperature. Resolution 1/3500. Voltage: 10 VDC (500 Ohm max. load). Current: 20 mA (500 Ohm load max.). Galvanically isolated from the signal input up to 500 V for 1 min.