Entrance area:

+/- 24 mVDC or +/- 240 mVDC

Display:

Backlit dimmable LCD display
Upper line: 6-digit, three-color (red, green, orange) with 18 mm digits
Lower line: 9-digit, green with 8.9 mm digits

Physical unit:

A physical 3-digit (red, green or orange) unit can be easily programmed from a list.

Indicators:

Four red backlit indicators for switching outputs.

Buttons:

4 push buttons on the front, 2 of which are freely programmable function buttons.

Resolution:

24 bits of the internal A/D converter.

Update rates:

A/D conversion rate: programmable from 5 to 160 measurements/sec.
Display update: 1 to 20 updates/sec.
Switching output: delay time from 0 to 3275 sec.
Analog output: update time from 0 to 10 sec.

Error messages:

"OLOL" - input signal is greater than the + signal range
"ULUL" - input signal is smaller than the - signal range
"...." - Display value exceeds upper display value
"-....." - Display value falls below lower display value

Data backup:

Non-volatile data memory

Entrance areas:

The accuracy in the following range table is given as a percentage of the display value. The maximum/permanent measuring signal must not exceed 30 V. The measuring range can be set via jumpers.

Sensor connection

as 4-wire (differential) or 2-wire.

Sensor supplies:

Ext. sensor supply selectable via jumper:
+ 5 VDC @65 mADC max. ; +/-2%
+ 10 VDC @125mADC max. ; +/-2%
Temperature coefficient: 20 ppm/°C max.

User input:

Three programmable user inputs NPN- or PNP-switching,
Response time: 12 msec,
max. input signal: 30 VDC
NPN switching
(20 k pull-up resistor to +3.3 V :
Active at V <1.1 V;
Inactive at V >2.2 V
PNP switching
(20 k pull-down resistor):
Active at V >2.2 V;
Inactive at V <1.1 V

Sum function:

Time base: second, minute, hour or day
Batch counter: Summation of the display value via user input
Time accuracy: 0.01% typical
Scaling factor and decimal point freely programmable; low signal suppression.

Power supply:

40 to 250 VAC, 50/60 Hz, 14 VA
or 21.6 VDC to 250 VDC, 8W

Resolution:

24 bits of the internal A/D converter.

Protection class:

Jet-proof and dust-tight to IP65 from the front.
Rear protection class IP20.

Housing:

Black, impact-resistant plastic housing made from a single cast.
The electronic slot can be pulled out to the rear.
The plug-in cards can be installed very easily.
Dimensions:
W 97 mm x H 50 mm x D 105 mm. Panel cut-out according to DIN: 92 mm
x 45 mm. Fastening via mounting frame with clamping screws.

Physical unit:

A physical 3-digit (red, green or orange) unit can be
orange) unit can be easily programmed from a list.
from a list.

Entrance areas:

The accuracy in the following range table is given as a percentage of the display value. The maximum/permanent measuring signal must not exceed 30 V. The measuring range can be set via jumpers.

Programming:

Programming is carried out either via the integrated USB interface and the free Crimson 2 programming software or via the four front buttons. The simple and logically structured menu navigation allows very fast commissioning. In addition, access rights can be assigned, e.g. quick access to the switching points can be enabled.

Protection class:

Water jet-proof and dust-tight to IP65 from the front and IP20 protection from the rear.

Power supply:

40 VAC to 250 VAC, 50/60 Hz, 14 VA or 21.6 VDC to 250 VDC, 8 W

Relative humidity:

max. 85%. rH, non-condensing.

Ambient temperature:

Operation: 0 °C to +50 °C.
Storage: -40 °C to +60 °C.

Housing:

Black, impact-resistant plastic housing made from a single cast. The electronic slot can be pulled out to the rear. The plug-in cards can be installed very easily.

Dimensions:

W 97 mm x H 50 mm x D 105 mm.

Panel cut-out:

according to DIN: 92mm x 45 mm.

Fastening:

via mounting frame with clamping screws.

Connection:

Via screw terminals.

Weight:

approx. 227 g.

Scope of delivery:

Device, fixing material, seal, operating instructions.

Customs tariff number:

9030 33 70

Manufacturer:

Red Lion, USA

Output cards:

The device can be easily upgraded with various output cards. output cards. Each device can be equipped with a maximum of one interface card, one relay or transistor output card and one analog output card.

Pluggable interface card:

1. half-duplex RS232, programmable (terminal strip or plug).
2. multipoint RS485, programmable (terminal strip or plug).
3. DeviceNet, programmable.
4. PROFIBUS-DP, programmable.

Pluggable relay output cards:

• 2 x relay changeover contact 5 A at 120/240 VAC or 28 VDC (ohmic load), at 120 VAC (80 VA inductive load). Service life of the relays is 100,000 cycles at max. load. The service life increases with lower loads.
• 4 x NO relay 3 A at 240 VAC or 30 VDC (resistive load), at 120 VAC (80 VA inductive load). Service life of the relays is 100,000 cycles at max. load.

Pluggable transistor output cards:

• 4 x NPN-OC transistors: max. 100 mA at Vsat = 0.7 V, Vmax 30 V, galvanic isolation of 500 V against the signal input.
• 4 x PNP-OC transistors: Internal supply: 24 VDC +/-10%, max. 30 mA all 4 transistors. External supply: max. 30 VDC, 100 mA for each individual transistor.

Pluggable analog output card:

Selectable output signal: 0/4 mA to 20 mA, 0 VDC to 10 VDC. Digitally scalable, offset. Accuracy: 0.17 % of range at 18 °C to 28 °C operating temperature, 0.4 % of range at 0 °C to 50 °C operating temperature. Resolution 1/3500. Voltage: 10 VDC (500 Ohm max. load). Current: 20 mA (500 Ohm load max.). Galvanically isolated from the signal input up to 500 V.