Entrance:

NPN, PNP sensors, CMOS, TTL, potential-free contacts, permanent magnet sensors are accepted. Setting via DIP switch. Attenuation adjustable to 50 Hz.
Minimum input frequency: 0.01 Hz
Max. input frequency Input frequency: up to 34 kHz

a. 1 meter A or B, or 1 tachometer:

Operating mode:
Single pulse input, cut-off frequency max. 34 kHz
Simple phase discriminator, cut-off frequency max. 22 kHz

b. 2 meters or 1 meter and 1 tachometer:

Operating mode:
Single pulse input, max. cut-off frequency 13 kHz
Single pulse input + 3rd counter, max. cut-off frequency 12 kHz
Simple phase discriminator x1, max. cut-off frequency 7 kHz
Simple phase discriminator x1 + 3rd counter, cut-off frequency max. 6 kHz

Note:

Please note:
The cut-off frequency is reduced when the following functions are used:
2 or 4 limit values (option),
Pulse output,
3rd counter,
Pulse output with 2-fold evaluation,
Phase discriminator with 2-/4-fold evaluation,
serial communication.

The specified limit frequencies are not affected when using the analog output (option).

Display:

6-digit, 14mm high red LED.

Counter: max. + 999,999 or -99,999 in static display,
max. +/-99,999,999 in 2 alternating displays
(OF 99) (999999)/(OF -99) (999999)
Tachometer: Accuracy: +/- 0.01%, period duration measurement,
max: 99.999
Min/max value: Display: L12345 or H12345.
Slave display: Alphanumeric characters can be sent to the
characters can be sent to counter C via the interface. This
displays 6 digits: 0 to 9, A, b, C, d, E, F, g, H, I, J, L, N, O, P, q, r, S, t, u, y and z Dot, comma, hyphen (minus) and space

Scaling:

All 3 counters and the speedometer can be scaled independently of each other.

Indicators:

A, B, C: Counter A, B, C
SP 1 to 4: Output 1 to 4 is active

Programming on the device:

Programming is possible if the programming lock input is not activated. All necessary parameters can then be set using the 5 front buttons. Programming is organized in individual sections. You are guided through the entry of the individual parameters with short symbols. In addition, parameterization using Crimson 2 software is possible in conjunction with an optionally available USB interface card.

User inputs:

3 programmable inputs are available
available. They can be set to PNP or NPN switching via jumpers.
via jumpers. Maximum input 30 VDC.
NPN: Active V < 0,9 VDC, Inaktiv V > 2.4 VDC
PNP: Active V > 2.4 VDC, Inactive V < 0.9 VDC.

Pulse output:

freely scalable ( factor : 0.0001 to 1.0000 ), NPN
O.C., max. 100 mA, 30 VDC

Power supply:

optionally 85 to 250 VAC 50/60 Hz, 18 VA
or 11 to 36 VDC, 14 W or 24 VAC +/-10 %, 15 VA.

Sensor supply:

12 VDC, +/-10%, max. 100 mA, short-circuit proof.

Protection class:

Jet-proof and dust-tight to IP 65 from the front.

Housing:

Dark red, impact-resistant plastic housing. The electronic slot can be pulled out to the rear. The plug-in cards can be installed very easily.

Dimensions:

W 97 mm x H 50 mm x D 104 mm.
Panel cut-out according to DIN: 92 mm x 45 mm.

Fastening:

Via mounting frame with clamping screws.

Connection:

fixed terminal strips.

Relative humidity:

max. 85 %. rH, non-condensing.

Ambient temperature:

Operation: 0 °C to +50 °C.
With all 3 cards fitted: 0 °C to 45 °C.
Storage: -40 °C to +60 °C.

Weight:

approx. 300 g (without plug-in options).

Scope of delivery:

Device, fixing material, seal, operating instructions.

Customs tariff number:

9029 20 38

Manufacturer:

Red Lion Controls, USA.

Output cards:

The device can be very easily upgraded with different output cards. Each device can be equipped with a maximum of one interface card, one relay or transistor output card and one analog output card. You can easily install the cards yourself.

Pluggable interface card:

1. half-duplex RS232, programmable
2. multipoint RS485, programmable
3. DeviceNet, programmable
4. PROFIBUS-DP, programmable
5. ModBus, programmable (via RS485 or RS232 interface)

Pluggable relay output cards:

1. 2x relay changeover contact 5 A at 120/240 VAC or 28 VDC (ohmic load), at 120 VAC (90 VA inductive load). Service life of the relays is 100,000 cycles at max. load. The service life increases with lower loads.

2. 4x NO relay 3 A at 240 VAC or 30 VDC (resistive load), at 120 VAC (70 VA inductive load). The service life of the relays is 100,000 cycles at max. load. The service life increases with lower loads.

Pluggable transistor output cards:

1. 4x NPN-OC transistors: max. 100mA at Vsat = 0.7 V, Vmax 30 V, galvanic isolation of 500 V for 1 minute against the signal input.

2. 4x PNP-OC transistors: Internal supply: 24 VDC +/-10 %, max. 30 mA all 4 transistors. External supply: max. 30 VDC, 100 mA for each individual transistor.

Pluggable analog output card:

Selectable output signal: 0 to 20 mA, 4 to 20 mA, 0 to 10 VDC. Digitally scalable, offset.
Accuracy: 0.17 % of range at 18 °C to 28 °C operating temperature;
0.4 % of range at 0 °C to 50 °C operating temperature.
Resolution: 1/3,500
Load: 0 VDC to 10 VDC at min. 10 kOhm;
0/4 to 20 mA at max. 500 Ohm.
Galvanically isolated from the signal input up to 500 V for 1 minute.