Entrance

NPN, PNP sensors, CMOS, TTL, potential-free contacts, permanent magnet sensors are accepted. Setting via DIP switch. Attenuation adjustable to 50 Hz.

Operating modes

Addition or subtraction with direction detection, difference, sum, phase discriminator x1, x2, x4 can be set.

Cut-off frequency

maximum 34 kHz

Housing

Dark red, impact-resistant plastic housing. The electronic slot can be pulled out to the rear. The plug-in card is very easy to install.

Display

6-digit, 14 mm high red LED.
max. + 999.999 or -99.999 in static display,
max. +/-99,999,999 in 2 alternating displays (OF 99) (999999)/(OF -99) (999999).

Scaling

All 3 counters can be scaled independently of each other

Indicators

A, B, C Counter A, B, C
Sp1 - 4 Output 1 - 4 is active

Operating modes of the 3rd counter C

Counter: Counter A
Total: Counter A + Counter B
Difference: Counter A - Counter B
(Independent scaling independent of counters A and B.)

Keys

The device is programmed and operated using the 5 push buttons on the front.

User inputs

3 programmable inputs are available. They can be set to PNP or NPN switching via jumpers.
Maximum input 30 VDC.
NPN:
Active_{Vin <} 0.9 VDC,
Inactive_Vin > 2.4VDC
PNP:
Active_Vin > 2.4 VDC,
Inactive_Vin < 0.9 VDC
Response times: max. 6 ms, with reset, gate and buffer memory, the device responds 25 μs after the next active edge of the assigned counter. A new edge is detected on the BE after max. 100 ms.

Power supply

PAXC0020/PAXC002B:
85 VAC to 250 VAC, 50/60 Hz, 18 VA
PAXC0030/PAXC003B:
11 VAC to 36 VDC, 14 W or
24 VAC ±10 %, 15 VA

Sensor supply

12 VDC, +/-10%, max. 100 mA, short-circuit proof

Protection class

Water jet-proof and dust-tight from the front in accordance with IP 65

Housing:

Dark red, impact-resistant plastic housing. The electronic slot can be pulled out to the rear. The plug-in card is very easy to install.

Dimensions:

W 97 mm x H 50 mm x D 104 mm.

Panel cut-out:

according to DIN: 92 mm x 45 mm.

Fastening:

via mounting frame with clamping screws.

Connection:

Fixed terminal strips

Relative humidity:

max. 85 %. rH, non-condensing.

Ambient temperature:

Operation: 0 °C to +50 °C.
Equipped with the limit value card:
0 °C to 45 °C.
Storage: -40 °C to +60 °C.

Weight:

approx. 300 g (without plug-in option).

Scope of delivery:

Device, fixing material, seal, operating instructions.

Customs tariff number:

9029 10 00

Manufacturer:

Red Lion, USA.

Output cards:

The device can easily be upgraded with a limit value card.

Pluggable relay output cards:

• 2 x relay changeover contact 5 A at 120/230 VAC or 28 VDC (ohmic load), 90 VA inductive load at 120 VAC. Service life of the relays is 100,000 cycles at max. load. The service life increases with lower loads.
• 4 x NO relay 3 A at 250 VAC or 30 VDC (resistive load), 70 VA inductive load at 120 VAC. Service life of the relays is 100,000 cycles at max. load. The service life increases with lower loads.

Pluggable transistor output cards:

• 4 x NPN-OC transistors:
  max. 100mA at _Vsat = 0.7 V, _Vmax 30 V, galvanic isolation of 500 V against the signal input.
• 4 x PNP-OC transistors:
  Internal supply: 24 VDC ±10%, max. 30 mA all 4 transistors.
  External supply: max. 30 VDC, 100 mA for each individual transistor.

Programming on the device:

Programming is possible if the programming lock input is not activated. All the necessary parameters can then be set using the 5 front buttons.