Entrance areas:

Thermocouple type:
K, S, R, J, T, N, B, E, C(W5/W26)
Temperature sensor (2- or 3-wire):
Pt100 alpha = .00385
Pt100 alpha = .00392
NI120 alpha = .00672
CU10 alpha = .00427
Voltage:
± 200 mVDC;
± 2 VDC;
± 20 VDC;
± 60 VDC
Current:
± 200 µADC;
± 2 mADC;
± 20 mADC;
± 200 mADC;
± 2 ADC
Potentiometer:
100 Ohm,
1000 Ohm,
10 KOhm

Accuracy:

Current input:
± 200 µADC = 0.12% + 0.04 µA
± 2 mADC = 0.12% + 0.4 µA
± 20 mADC = 0.12% + 4 µA
± 200 mADC = 0.12% + 0.40 µA
± 2 ADC = 0.7% + 0.4 mA

Voltage input:
± 200mVDC = 0.12% + 40 µV
± 2 VDC = 0.12% + 0.4 mV
± 20 VDC = 0.12% + 4mV
± 60 VDC = 0.12% + 40mV

All specifications refer to a temperature range of -10 °C to + 55°C.

Resolution:

Current input:
± 200 µADC = 10 nA
± 2 mADC = 0.1 µA
± 20 mADC = 1 µA
± 200 mADC = 10 µA
± 2 ADC = 0.1 mA

Voltage input:
± 200mVDC = 10 µV
± 2 VDC = 0.1 mV
± 20 VDC = 1 mV
± 60 VDC = 10 mV

A higher resolution can be achieved by input scaling.

Input impedance:

Current input:
± 200 µADC; ± 2 mADC; ± 20 mADC = 100 Ohm
± 200 mADC; ± 2 ADC = 0.06 Ohm

Voltage input:
All ranges 625 KOhm

Thermocouple:
20 MOhm

Display:

4.3" or 3.5" color TFT display with analog resistive touchscreen

3.5" display:
Colors: 262,144 K
Pixels: 320 x 240
Brightness: 540 cd/m²
LED backlight service life: 30,000h*

4.3" display:
Colors: 262,144 K
Pixels: 480 x 272
Brightness: 420 cd/m²
LED backlight service life: 30,000h*

*at room temperature (25 °C)

A/D conversion:

programmable from 5 to 200 measurements per second.

User inputs:

Two programmable user inputs
Max. Input voltage: 30 VDC

Sink:
Active: _VIN < 0.9 VDC
Inactive: _VIN > 2.4 VDC
20 KOhm pull-up at 3.3 V

Source:
Active: _VIN > 2.4 VDC
Inactive: _VIN < 0.9 VDC
20 KOhm pull-down

SSR outputs (OnBoard):

2 outputs, only SINK or SOURCE mode available, not separately adjustable.

Sink mode (NPN):
Type: Switched DC, N-channel open-drain MOSFET
Max: 100 mA
VDS ON: 0.3 V @ 100 mA
VDS MAX: 30 VDC
Leakage current in off-state: 0.5 mA max

Source mode (PNP):
Type: Switched DC, P-channel open-source MOSFET
Max: 100 mA
VDS ON: 0.3 V @ 100 mA
VDS MAX: 30 VDC
Leakage current in off-state: 0.5 mA max

Sensor supply:

24 VDC, ±5%; @max. 50 mA
Reference voltage: + 2 VDC, ± 2%
Reference current: 1.05 mADC, ± 2%

RS485 interface (OnBoard):

Uses the Modbus RTU protocol (RS485)
Baud rate: Up to 115,200
Data format: 7 or 8 bit; odd, even or no parity; 1 or 2 stop bits
Isolation: 500 Vrms to sensor, user voltage and digital inputs.
Not isolated to semiconductor outputs

Power supply:

10 VDC to 30 VDC; 4.6 W (without modules)
Max. Power consumption: 12 W (with modules)
Isolation: 500 Vrms for 1 min. to all inputs and outputs.

WiFi 4:

Output power up to 20.5 dBm
Frequency: 2412 MHz to 2484 MHz
Channels: 1 to 13
Note: Channel/frequency limitation is based on the configured country/region code.
Wi-Fi compliance: TCP/IP; 802.11 b/g/n

Modbus TCP communication via WiFi 4 possible.

Memory:

Non-volatile memory, retains all programmable parameters and display values
Memory card: microSD cards of up to 32 GB in FAT16/FAT32 format possible

Totalizer:

Time base: second, minute, hour or day
Batch counter: Can totalize measured values / Trigger: User input
Time accuracy: 0.01% typical
Decimal point: 0 to 0.0000
Scaling factor: 0.001 to 65.000
Display range: -199,999 to 999,999

Linearization:

Data point pairs: Selectable from 2 to 40
Display range: -199,999 to 999,999
Decimal point: 0 to 0.0000

Ambient conditions:

Operating temperature range: -10 °C to +55 °C
Storage temperature range: -20 °C to +60 °C
Humidity during operation and storage: 0 % to 85 % rH, non-condensing
Altitude: Up to 2000 meters

Vibration and shock:

Vibration: 5-500 Hz, 2 g
Shock: 20 g (10 g relay)

Dimensions (WxHxD):

PM500A0301600F00:
Installation dimensions (WxHxD): 44.8 mm x 44.8 mm x 87.17 mm
Height without terminal strips
Depth specification corresponds to basic device incl. rear cover
Installation depth with max. number of modules: 189.47 mm
Panel cut-out: DIN 45 x 45
Display/front (WxHxD): 95.09 mm x 82.09 mm x 14.25 mm
Rear cover (B): 11 mm

PM500A0400800F00:
Installation dimensions (WxHxD): 91.95 mm x 44.8 mm x 92.20 mm
Height without terminal strips
Depth specification corresponds to basic device incl. bus connector for PM-50 4.3"
Installation depth with max. number of modules: 160.40 mm
Panel cut-out: DIN 92 x 45
Display/front (WxHxD): 123.59 mm x 84.91 mm x 14.25 mm
Bus connector rear cover (B): 15 mm

Max. Sheet thickness: 6.35 mm
Min. sheet thickness for NEMA 4X/IP65 requirements: 1.02 mm

Housing:

One-piece cover/housing.
Flame retardant.
Installation seal and installation fastening included

Weight:

3.5" device: approx. 224 g
4.3": device approx. 321 g

Protection class:

Type 4X for indoor use only
IP65 (front)
IP20 (rear)

Certificates:

CE, UKCA, FCC, UL,

Scope of delivery:

PM500A0301600F00:
1x rear cover
2x 2x locking clip for shock and vibration applications
1x mounting frame

PM500A0400800F00:
1x empty module
1x Bus connector rear cover for PM-50 4.3" display
2x 2x locking clip for shock and vibration applications
1x mounting frame

Relay output (accessory):

PMM000I0RL200000:
2 x changeover contacts; switching capacity: 5 A at 250 VAC or 30 VDC; resistive load

PMM000I0RL400000:
4 x NO contacts;
Switching capacity: For one relay 3 A at 250 VAC or 30 VDC; resistive load
When using all relays switching capacity max. 1A/relay

Analog output (accessory):

PMM000I0AN000000:
0/4 mA to 20 mA or
0 VDC to 10 VDC
±10 VDC
Effec. Resolution: 16-Bit

RS232 interface (accessory)

PMM000CM23200000:
Possible baud rates: 300 to 115,200 bit/s
Data bits: 7 or 8
Parity: ungrade, grade or no parity

Ethernet interface (accessory):

PMM000CMENT00000:
10/100 T-Base
Auto MDI / MDI-X
RJ-45 socket
ModbusTCP communication possible.

AC supply (accessory):

PMM000PWACP00000:
Input: 85 VAC to 240 VAC; ±10%; 0.16 A to 0.3 A
Frequency: 50/60 Hz
Output: +15 VDC; ±10%; 0.8 A; max. 12 W
Insulation: 3 kV between primary and secondary side

Note:
The AC supply module must always be mounted in the last position of the communication flow.

Manufacturer:

Red Lion